General Info Page

General Pricing

(Not All Services Are Listed)

(Some Jobs Are Custom Pricing Only)

PLEASE REVIEW POLICIES PAGE

FOR DEPOSIT INFORMATION!

IMPORTANT NOTES:

OUR JOB IS ONLY AS GOOD AS THE INSTALL & TUNE!!!!

OUR TIME IS JUST AS VALUABLE AS YOURS!

WE DO NOT MAKE CUSTOM PARTS!

WE ARE NOT A MACHINE, TOOL, OR EQUIPMENT RENTAL SERVICE.

*Pricing is subject to change at any time*

Hourly Rate	Starting Hourly Rate is $160	$160-$175/Hour
Hot Tank/Clean Block(s)	4, 6, or 8 Cylinder Blocks (Prices Vary) Block Preparation (for cleaning) time is extra Drilling & removing stuck oil gallery plugs, and etc. is an example.	$160-$270
Bore & Finish Hone (including final wash after hone)	Torque Plate Honing is additional	Starting @ $62.50 Per Cyl.
Jetwash OR Hot Tank & Media Blast Cylinder Head/Heads	Varies from 4, 6, or 8 cylinder heads Gas & Diesel Prices Listed	$160-$300
Pressure Test Cylinder Head/Head(s) Aluminum OR Cast Iron (Some are Custom Pricing)	Varies from 4, 6, or 8 Cylinder Heads Diesel Or Gas	$80-$150+ Ea.
Magnaflux Cylinder Head (Cast Iron Only)	Varies from 4, 6, or 8 cylinder heads *Some are (custom) pricing	$60-$110 Ea.
Magnaflux (Diesel) Cylinder Head (Cast Iron Only)	Varies from 4, 6, or 8 cylinder heads *Some are (custom) pricing	$75-$250 Ea.
Valve Job Work (8,16, & 32 valve) *Includes Reassembly After Valve Job	All Standard Valve Jobs are 3 Angle	$280-$640 (Will Vary)
Valve Guide Replacement (8,16, & 32 valve) *OEM Replacement Valve Guides, Bronze Guides/Guide liners	OEM Replacement guides to Bronze valve guides Bronze valve guides need reamed/fit per the valve stem diameter OEM Cast Iron/Hot Rod cylinder heads have the Bronze Liner option	$280-$600 (Will Vary)
Pocket Porting	(Most) 8, 16, 20, 24, & 32 Valve Cyl. Heads Inquire within on your project	Starting at $475+
Resurface Cyl. Head Diesel Cyl. Heads- (Priced Higher)	Starting @ ($25 Per Cylinder)	$100-$320
Align Hone (With or Without ARP Hardware)	Studs or bolts, (Girdle Work Is Additional) Aluminum blocks need additional time (email to discuss the process)	$300+
Square Deck V8 Block W/BHJ Block Tru	Clean Up Resurface	$300+
Resurface/Deck Inline 4 Or 6 Cylinder Block	Clean Up Resurface	Starting at $220-$270
Flywheel Resurface (Car/Light Truck-Heavy Duty)	Car/Light Truck Flat (1) Surface ($60) Car/Light Truck (Recessed-2 Surface Cut)- (Starts @ $70) Heavy Duty- Starts @ $130+	Start @ $60-$160 Call/Email for price!

V8 (16 & 32 Valve) Cylinder Head (Labor)

*Standard Light Truck & Passenger Car V8 Heads*

*Race Cylinder Heads Require More Time*

*NO PARTS*

*All Cylinder Heads need to be disassembled to valves/valve springs only*

16 Valve

Disassemble, Clean & Blast- $185-$250 (If extreme carbon build-up is found)

*cylinder heads that are disassembled to valves/springs only*

Pressure Test (Each)- (Starting @ $75 each)

Standard 3-Angle Valve Job- (Starting @ $350)

Resurface (Pair)- $220

(Deposit Needed)- $325+tax (Cleaning & Crack Detection)

32 Valve (Labor)

Disassemble, Clean, & Blast- $300

Pressure Test (each)- $75+ (May Vary)

Replace Valve Guides (All 32) (Standard OEM Guides)- $450-$600 (Bronze)

Standard 3-Angle Valve Job- $540

(Includes Reassembly)

Resurface (Pair)- $240 (Starting-May Vary to complexity of setup)

*Call/Email to Discuss Deposit*

*We are not responsible for Injectors, Exhaust Manifolds, and/or other misc. sensors/accessories you leave on. Any component left on upon drop off that is not related to the work we are doing for you; we will not be responsible for.

The time it takes to remove those parts will be billed.

4 Cylinder (16 Valve) Cylinder Head (Labor)

Disassemble, Clean, & Blast- $140

*Additional time added if cylinder head accessories & etc. are installed*

Pressure Test- $75+ (May Vary)

Replace Valve Guides (All 16) (Standard OEM Guides)- $160

*Bronze Valve Guide Replacement (Labor Only)- $330

Standard 3-Angle Valve Job- $400+

(Includes Reassembly)

Resurface- $95-$135

*Call/Email to Discuss Deposit*

*Extra information*

If this is a performance cylinder head, and bronze valve guides are used, they need installed & fit.

That will start at ($330).

Pocket Porting (Starts @ $475)

Ask with your inquiry to discuss options!

All overhead cam cylinder heads will be Baking Soda blasted, instead of glass bead blasted, for safety of build-up in oil galleries/small areas.

The Soda Blast unfortunately, does not give a great appearance, but it is the safer solution.